AM-001 carbine replica
- Material: plastic + metal
- Weight: 1745g
- Length: 360-600mm
- Colour: black
- Initial muzzle velocity: ~300 FPS
- Drive: electrical
- Manufacturer: Amoeba Airsoft
AM-001 carbine replica
A series of the latest Amoeba Airsoft replicas is based on a well-known design of AR type assault rifles, however these replicas have been considerably modified and enriched of many constructional details and interesting technical solutions, which improve not only their functionality but also their look. Thanks to its compact dimensions, AM-001 is very handy and constitutes a perfect tool during airsoft CQB actions.
The replica's receiver was made of strengthened nylon. Quality of the materials used results in the fact that it is very difficult to recognise on the first sight whether it's plastic or metal. Effective signs of a model, calibre and Amoeba Airsoft's logo were engraved on the receiver. Metal was used to produced the outer barrel, the front-sight, the flash hider, the stock tube and some small pieces. The pistol grip, properly shaped, covered with scrabrous non-slip texture which improves grip and comfort. The magazine release button was enlarged in order to make its usage easier.
The replica was equipped with a light plastic stock folded to the side. The battery is located in the upper part of the receiver. Access to a hop-up system regulation is achieved in a standard for this design way - by pulling the charging handle and opening tjhe shell ejector..
The all-purpose 22mm RIS rails are situated on the front grip and on the top of the receiver, thanks to which the replica may be fitted with a wide range of additional accessories, from a scope to lighting and tactical grips. The rifle has iron sights mounted on the RIS rail. A vertical front grip goes together with the replica.
The outer barrel ends with a 14mm right-hand thread on which the flash hider was mounted.
Amoeba Airsoft's replicas make it possible to replace the spring quickly, with no necessity of dismantling the gearbox. The heart of the replica is a bit strengthened modified gearbox v. 2, which possesses an integrated EFCS module - Electronic Firing Control System. It controls the operation of the trigger mechanism, resulting in a very smooth work and shorter engine reaction. A standard trigger swich assembly was replaced by an electronic system. The EFCS also has a built-in MOSFET system.
EFCS considerably increases the mechanism's life span and the whole replica as well and it allows to use high-voltage batteries, including LiPo. If we buy an outer dedicated EFCS programmer, we may receive a possibily to select fire modes as well as the burst mode (a three BBs series).
The magazine which goes together with the replica is a hi-cap with capacity of 300 BBs. The magazine's case was made of steel.
The set does not include a battery and a charger.
The set includes:
- replica
- magazine
- manual
- vertical, RIS mounted front grip
NiCd
rechargeable battery is characterized by high efficiency
current-carrying capacity, but there are disruptive effect on memory.
Should be unloaded and loaded in the full cycle, ie, it is recommended
to fully discharge, and after unloading must charge the battery
immediately without leaving it for a long time in a discharged state.
NiMH batteries have a higher self-discharge over time and shorten the
life - on the other hand, they earn about 30% more capacity.
Blow back is a simulation system of the cocking lever - it imitates the work of it as the equivalent sharp. This system raises the realism and adds a lot more experience during shooting.
It is the spped of bb, while its leaving the innerbarrel of replica. This speed is measured in FPS (Feet Per Second).
1 FPS = 0,3 m/s
1 J = 99 m/s
1 J = 326,7 FPS
Indications v2, v3, v6 does not mean the level of advance, but only shape of gearbox skeleton which was used and selected by the manufacturer depending on the capabilities of the body of the replica. For example, a models of the M4/M16 family, MP5, have a v2 gearbox, while the AK family have gearbox v3.
Hop-Up system is used for overclocking bb during the shot (putting it in rotation), through which, it extends its flight path. Acting laws of physics make that bb lift up, while the gravitational force take it down. Appropriate adjustment of Hop-Up, will compensate for these two factors, which result in long and straight flight for longer distance and be greater focus shot (to improve accuracy).